1.特殊的情况需进行计算:
A、求加热器功率或冷冻功率 KW=W×△t×C×S/860×T
W=模具重量或冷却水 KG
△t=所需温度和起始温度之间的温差。
C= 比热 油(0.5),钢(0.11),水(1),塑料(0.45~0.55)
T=加温至所需温度的时间(小时)
B、求泵的大小
需了解客户所需泵浦流量和压力(扬程)
P(压力Kg/cm2)=0.1×H(扬程M)×α(传热媒体比重,水=1,油=0.7-0.9)
L(媒体所需流量L/min)=Q(模具所需热量Kcal/H)/C(媒体比热水=1 油=0.45)×△t(循环媒体进出模具的温差)×α×60
2.冷冻机容量选择
A、Q(冷冻量Kcal/H)=Q1+Q2
Q1(原料带入模具的热量Kcal/H)=W(每小时射入模具中原料的重量KG)×C×(T1-T2)×S(安全系数1.5~2) T1 原料在料管中的温度;T2 成品取出模具时的温度 ;Q2 热浇道所产生的热量Kcal/H
B、速算法(有热浇道不适用)
1RT=7~8 OZ 1OZ=28.3g(含安全系数)
1RT=3024Kcal/H=12000BTU/H=3.751KW
1KW=860 Kcal/H 1 Kcal=3.97BTU
3、冷却水塔选用=A+B
A、射出成型机用
冷却水塔RT=射出机马力(HP)×0.75KW×860Kcal×0.4÷3024
B、冷冻机用
冷却水塔RT=冷冻机冷吨(HP)×1.25
根据加工不同塑料所需要的模具温度来选择模温机
塑料模化合物 |
简要描述 |
模具温度 ℃ |
Plastic moulding compound |
Short description |
Mould wall temp in ℃ |
聚乙烯,高密度/Polyethylene ,high density |
HDPE |
10 - 40 |
聚乙烯,中密度/Polyethylene ,medium density |
LDPE |
10 - 40 |
聚丙烯/Polyepropylene |
PP |
10 - 50 |
聚苯乙烯/Polystyrene |
PS |
10 - 60 |
液晶聚合物/Liquid crystal Polymers |
LCP |
30 - 150 |
聚氯乙烯/Polyvinyl chloride |
PVC |
40 - 60 |
聚酰胺/Polyamid |
PA |
40 - 60 |
丙烯腈-丁二烯苯乙烯-丙烯腈 |
ABS |
40 - 70 |
苯乙烯-苯乙烯共聚物/Styrol-Acrylnitril |
SAN |
40 - 70 |
聚甲基丙烯酸甲酯/ Polymenthylmethacrylate |
PMMA |
50 - 80 |
聚酰胺6.6/ Polymide 6.6 |
PA6.6 |
60 - 120 |
聚对苯二甲酸丁二醇酯/Polyethylene terephthalate |
PET |
60 - 140 |
聚酰胺6 /Polyamide 6 |
PA 6 |
70 - 90 |
聚对苯二甲酸丁二酯/Polybutylene terephthalate |
PBTP |
70 - 140 |
聚丁烯氧化物/ Polyphenylene oxide |
PPO |
70 - 150 |
聚砜 / Polysulphone |
PSU |
70 - 190 |
聚甲醛 / Polyoxymethylene |
POM |
80 - 120 |
聚碳酸酯 / Polycarbonate |
PC |
80 - 150 |
聚亚苯基硫化物 / Polyphenylene sulphide |
PPS |
80 - 180 |
聚醚酰亚胺 / Polyether imide |
PEI |
90 - 180 |
聚亚苯基sul fon / Polyhenylensulfon |
PPSU |
100 - 170 |
聚醚砜 / Polyther sulphone |
PES |
120 - 190 |
聚醚醚酮 / Polyetheretherketone |
PEEK |
160 - 180 |